Professional heating, cooling & air quality services serving Corning and surrounding communities in New York. NATE-certified, 24/7 emergency response.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Air conditioning failures range from simple capacitor replacements to complex compressor and refrigerant circuit repairs requiring EPA Section 608 certified handling. Our technicians diagnose the root cause using superheat and subcooling measurements, amp draws, and pressure readings to restore full cooling output.
Properly sealed and insulated ductwork is essential for delivering rated BTU output to every room in your home. Our technicians repair collapsed sections, seal leaks with UL-listed mastic and mechanical fasteners, and verify balanced airflow across all supply registers after service.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Sudden HVAC failures often stem from compressor lockout, blown transformer fuses, failed gas valves, or tripped high-pressure switches. Emergency repair service provides same-day response with technicians equipped to diagnose and resolve critical faults across all major heating and cooling equipment brands.
Maintaining safe and efficient boiler operation requires precise attention to water chemistry, flue gas temperatures, and combustion efficiency. Professional repair addresses leaking heat exchangers, malfunctioning aquastats, air-bound radiators, and ignition system failures to restore rated AFUE output.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Indoor air quality suffers when ductwork harbors years of accumulated particulate matter, allergens, and biological growth. Thorough duct cleaning addresses every branch run, main trunk line, and register boot using agitation tools and high-powered vacuum extraction to restore clean airflow.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
Corning, NY is home to 10,613 people and a wide variety of heating and cooling systems — from central forced air to radiant boilers to ductless mini splits. KIC Refrigeration has worked on every HVAC configuration across the Corning area. That hands-on experience means we know exactly which equipment brands and installation methods deliver the best performance in this region.
Our familiarity with Corning extends beyond HVAC equipment — we understand the neighborhoods, the local permitting process, and the seasonal weather patterns that stress every heating and cooling system in the area. When KIC Refrigeration takes on your project, you benefit from a team that factors in your home's age, insulation quality, and duct layout before recommending a single piece of equipment.
The certifications, standards, and commitments that set our HVAC service apart.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Every technician on our team holds current NATE certification — the highest standard in the HVAC industry for installation and service competency. You get a technician who has passed rigorous exams on system diagnostics, refrigerant handling, and equipment commissioning.
Get the information you need to make confident HVAC decisions for your property.
The ideal time for HVAC replacement in Corning is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in New York and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Corning including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
Most residential HVAC installations in Corning, NY are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
The National Air Duct Cleaners Association recommends professional duct cleaning every 3 to 5 years for most Corning homes. However, several factors can shorten that interval: households with pets that shed, family members with allergies or asthma, smokers in the home, and properties that have undergone recent renovation or construction work should consider cleaning every 2 to 3 years. Warning signs that your ducts need attention include visible dust or debris accumulating at register openings, musty or stale odors when the system runs, unexplained respiratory symptoms, and inconsistent airflow between rooms. Our NADCA-compliant cleaning process uses truck-mounted vacuum equipment and rotary brush agitation to remove dust, allergens, mold spores, and debris from your entire duct system. We also inspect for disconnected joints, damaged insulation, and air leaks that reduce system efficiency.
A comprehensive HVAC inspection from KIC Refrigeration in Corning covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
HVAC repair costs in Corning typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
Our reputation is built on honest service, skilled technicians, and systems that perform.
"These guys are the real deal. Boiler was making a terrible noise and they diagnosed the problem in minutes. Runs perfectly now."
"Mini split repair was done right the first time. The outdoor unit had a refrigerant leak and they found it, fixed it, and recharged the system same day."
"Dryer vent cleaning was quick and affordable. The technician showed me photos of the lint buildup — honestly had no idea it was that bad. Glad we got it done."
Professional heating and cooling services extending to neighboring cities and towns.